Correctly made AdBlue reads 32.5% on a refractometer's AdBlue (DEF, AUS 32 or urea) scale, and any reading from 31.8% to 33.2% is within the ISO 22241-1 limits. Below 31.8% the fluid has been diluted — usually with water. Above 33.2% it has become too concentrated, usually because water evaporated from an open or overheated container. Either way, it should not go into a vehicle until the cause is found.
What each reading means
| Reading on the AdBlue scale | What it usually means | What to do |
|---|---|---|
| About 0% | It is water, or the prism was not cleaned | Clean, recalibrate and test again |
| Below 31.8% | Diluted: water added, or a contaminated container | Do not use; quarantine and trace the source |
| 31.8–33.2% | Within ISO 22241-1 | Fine to use, if the packaging and storage check out |
| Above 33.2% | Too concentrated: water has evaporated | Do not use; check how and where it was stored |
| Far above 35% | Heavy evaporation, crystals in the sample, or the wrong scale | Re-read on the correct scale; take a fresh sample |
The ideal is 32.5%. Most good fluid reads within a few tenths of that.
Read the right scale
Many workshop refractometers combine three or four scales in one eyepiece: coolant freezing point (for ethylene and propylene glycol), battery acid specific gravity, screen wash — and AdBlue. Readings from the wrong scale cause most of the confusion.
- Look for the scale labelled AdBlue, DEF, AUS 32 or urea %. It is usually a short scale centred on 32.5%, often with the in-spec band marked.
- Some instruments show AdBlue as a freezing point instead. Correct AdBlue freezes at −11°C. A freezing point closer to 0°C means the fluid is diluted.
- A refractive index scale works too. ISO 22241-1 gives 1.3814–1.3843 at 20°C for AUS 32.
If your instrument has no AdBlue scale, it cannot tell you whether AdBlue is in specification.
How to take an accurate reading
- Calibrate first. Put two or three drops of distilled water on the prism, close the cover and set the line to zero with the calibration screw. Do this at room temperature.
- Let things settle to the same temperature. Most instruments have automatic temperature compensation (ATC), but it works best when the refractometer and the sample are both near 20°C. A sample straight from a hot drum in the sun can read wrongly.
- Take the sample from the middle of the container, not the surface or the dregs, using a clean pipette.
- Apply two or three drops, close the cover so the fluid spreads evenly with no bubbles, and wait about 30 seconds.
- Read against good light, where the blue and white fields meet.
- Clean the prism with distilled water and dry it with a soft cloth. AdBlue left on the prism dries to crystals and scratches the glass.
- Repeat once or twice. Two readings that agree are worth far more than one.
Digital refractometers do the same job and remove the guesswork of reading a line. Either type is accurate enough for an incoming-goods check.
What a refractometer cannot tell you
A refractometer measures one thing: concentration. AdBlue can read a perfect 32.5% and still be out of specification, because ISO 22241-1 also limits:
- Metals such as calcium, iron, copper and zinc, measured in fractions of a milligram per kilogram
- Phosphate, aldehydes and biuret
- Insoluble matter
None of these change the reading. They need laboratory testing to the methods in ISO 22241-2. That is why a good reading is a pass on one test, not a clean bill of health. Packaging, batch records and the supplier's documentation are the other half of the check — our ISO 22241 guide covers what to ask for.
When to test
- On delivery, especially from a new supplier or a new batch, before the fluid goes into a bulk tank
- After long storage in heat, which can concentrate or degrade the fluid — see our storage guide
- Whenever a vehicle shows an SCR or NOx warning soon after a refill
- If anything about the container looks wrong: broken seal, missing batch number, unusual smell
Keep a note of the date, batch number and reading. When a problem appears months later, that record is what lets you trace it.
Quick answers
What should AdBlue read on a refractometer?
32.5% urea on the AdBlue scale. Anything from 31.8% to 33.2% is within ISO 22241-1.
Is a reading of 32% acceptable?
Yes. 32.0% is inside the 31.8–33.2% band. A reading of 31.5% is not.
Why is my AdBlue reading too high?
Usually because water has evaporated — from a container left open, or stored hot for a long time. Crystals in the sample can also push the reading up.
Can I use a coolant refractometer for AdBlue?
Only if it has an AdBlue, DEF or urea scale. The glycol scales measure something else and their numbers do not translate.
Does a good reading mean the AdBlue is genuine?
It means the concentration is right. Diluted fakes fail the test, but contamination with metals or other impurities only shows up in a laboratory analysis.
Key points
- Good AdBlue reads 32.5%; 31.8–33.2% is within ISO 22241-1.
- Low readings mean dilution; high readings usually mean evaporation.
- Read the AdBlue/DEF/urea scale, not the coolant or battery scales.
- Calibrate with distilled water, test near 20°C and repeat the reading.
- A refractometer checks concentration only; impurities need a lab test.






